D-MAX DMS-200Se Instrukcja Użytkownika

MINI SPEED DOME CAMERA MINI SPEED DOME CAMERA USER MANUAL

Outdoor

3. DIRECTIONS FOR USE 1) DIP SWITCH SETTING -TERMINALATION RESISTOR (DIP S2/SW1) ~Turn the last camera on

2) HOW TO CHANGE PROTOCOL Set up this part. The switch that selects Protocol.

3) HOW TO SET ADDRESS DIP SWITCHES Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program. RX NO DIP SWITCH (HEX) RX N

4) HOW TO USE OSD MENU 4-1. HOW TO CONTROL OSD MENU OSD (ON SCREEN DISPLAY) CONTROL It is the function to call up the Menu ＊User can not only set P

4-1. FUNCTIONAL DESCRIPTIONS ON EACH MENU 1. ID SET. This function is to set camera ID up to 16 letters on the monitor. User can choose letters that t

4. AGC CONTROL AGC(Automatic Gain Control)- It adjusts the amount of video amplification to maintain a full 1-volt peak-to-peak video signal output au

8. FLICKERLESS Tremble on the screen is removed in the state of FLICKERLESS ‘ON’, the shutter speed, at the same time, is fixed in 1/120sec in NTSC a

11. SET BACK LIGHT MODE ▶ WDR MODE - Limit: Adjust the WDR Sensitivity by selecting Low or Max - Level: Adjust the WDR Brightness by controlling 0

14. ZOOM MAX Limit It is used when user corrects and limits the extensional range of the focus as a function to set the maximum value of zoom. ▶ Of

TABLE OF CONTENTS 1. CATION ------------------------------------------------------- 3 2. INTRODUCTION OF PRODUCT -------------------------------5

18. SELECT ALARM Set alarm mode you want to use. ▶ Sensor / Motion 19. Motion Detection If you want to use motion detection, set “On” mode. An

. •[SAVE]: Previous screen. [DELETE]: Remove. [ESC]: Cancel ② Preset PTZ set : Set the position of Preset Select the main menu with t

③ Preset Swing SET : Set Preset Swing Move next SWING page for the setting, if user presses F/F key in the state of selection of the menu ※The prese

⑤ Tour SET Group: User can set continual Group motion that can be put 12 Groups in 1 Tour Move to the setting page if user presses F/F key on this men

If user saves new positions without “DELETE”, all saved positions will be deleted automatically. 22. ALRAM CHANNEL ON/OFF - CH On/Off : Alarm Inpu

Home Position Preset The camera automatically moves to where master user set, when another user controls the camera to observe other area. (You

25. AUTO TILT MOVE The PAN is turned in a 180° degree arc automatically when the angle of the camera moves down to the maximum degree, therefore, it

29. SHORTCUT KEY The Shortcut Key can make some of the functions to perform faster and easily. ★ How to use shortcut key ( All protocols is oper

32. FACTORY RESET WARNING Please be careful of that all setting data of OSD MENU are reset into the first default when operates FACTORY RESET WARNING

4-3. SETTING FUNCTIONS BY KEYBOARD 1. Preset setting User can set Preset point up to 250. ① Preset Input ② Preset Move ③ Delete a separat

1. CAUTION Thank you for purchasing mini speed dome camera DMS-200. Please operate the product after being fully aware of the manual. Pease conta

3. Group setting ① Start Group setting mode Set Preset No. again in continual input. Set a GROUP again from the first after e

4. Tour set mode ① Tour set mode ② Start / End Tour ③ Delete Tour 5. Spiral Funct

6. PTZ Trace It memorizes P/T/Z motions for 200sec then operates them at the same Trace. ① Start / End Trace ② O

4-4. OSD MESSAGE DESCRIPTION 1. PRESET MESSAGE 2. SWING MESSAGE User can check that Preset No.1 is save

3. GROUP MESSAGE 4. TOUR MESSAGE 5. Spiral SEQ MESSAGE CAM-001 GP:01 P002,T001,S64

4. TROUBLE SHOOTING CAUTION IN USE • Make sure that turn the power switch off before installation. • Avoid the places where is the high/low temper

5. ASSEMBLES measurement Indoor Wall Mount Bracket It can be connected with D-max bracket by using mo

Outdoor Wall Mount Bracket ① Unscrew the 4 bolts of the bubble cover then separate the camera housing. ② -1

6. CONFIGURATIONS ▪ SUB KEYBOARD SETTING 1 2 3 255 DMS-200 MON

▪ SETTING ONE KEYBOARD : Control line : Video line

CAUTION IN USE. Do not disassemble the unit and put alien substances in the unit. It can cause troubles. Ensure power switch-off before the in

7. SPECIFICATION MODEL DMS-200 Signal system NTSC PAL Image sensor 410K Pixel, 1/4 " SONY Super HAD CCD Effective pixels 768(H) X 494(V),

2. INSTRUCTION OF PRODUCT 1). DESCRIPTION AND FEATURES - Description - This camera has been designed elegantly for buildings, department stores

2) INSTALLATION AND CONNECTION 2-1. NAME AND FUNCTION OF EACH PART

2-2. INSTALLATION Indoor Make 4 holes after attaching ceiling guide where the camera is set. Take

Outdoor Unscrew the 4 bolts of the bubble cover then separate the camera housing. Connect the pow

2-3. CONNECTION DIAGRAM Indoor AC24V/more than 1A VIDEO IN AUDIO IN